This part of EN ISO 13934 specifies a procedure for the determination of maximum force of textile fabrics known as the grab test. The method is mainly applicable to woven textile fabrics. It may be applicable to fabrics produced by other techniques. It is not normally applicable to woven elastic fabrics, geotextiles, nonwovens, coated fabrics, textile-glass woven fabrics and fa...

本标准规定了钢铁制件的热浸镀锌层（其它合金元素含量不超过2%）的一般性能和试验方法。 不适用于：a） 连续式热浸镀锌的板材和线材；b） 自动化设备热浸镀锌的管材和棒材；c） 具有特殊附加要求或与本标准要求不同的热浸镀锌产品； 本标准对热浸镀锌产品的后处理/保护涂层未做规定。 此第二版注销并取代第一版（ISO1461：1973）及第一版ISO 1459 （ISO1459：1977）。均对其作了技术性修改。...

This International Standard defines the requirements for grades of alloyed aluminium ingots intended for remelting. It specifies the classifications and designations applicable to these grades, the conditions in which they are produced, their properties and the required identification marking. This International Standard does not address the issue of radioactivity. Certain elem...

Technical Corrigendum 1 to ISO 17615:2007 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee SC 7, Aluminium and cast aluminium alloys.

This International Standard specifies a molecular absorption spectrometric method using 1, 10-phenanthroline for the determination of the mass fraction of iron in titanium and titanium alloys. The method is applicable to titanium and titanium alloys with a mass fraction of iron in the range from 0,005 % to 2,0 %. ISO 22960 was prepared by Technical Committee ISO/TC 79, Light me...

This International Standard specifies an atomic absorption spectrometric method for the determination of the mass fraction of iron in titanium and titanium alloys. The method is applicable to titanium and titanium alloys with a mass fraction of iron in the range from 0,005 % to 2,0 %. ISO 22961 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcom...

This International Standard specifies an infrared method after fusion under inert gas for the determination of the mass fraction of oxygen in titanium and titanium alloys. The method is applicable to titanium and titanium alloys with a mass fraction of oxygen in the range from 0,02 % to 0,4 %. ISO 22963 was prepared by Technical Committee ISO/TC 79, Light metal and their alloys...

This International Standard is one of a series of standards dealing with the sampling and testing of paints, varnishes and related products. It specifies a test method for assessing the resistance of paint coatings to separation from substrates when a right-angle lattice pattern is cut into the coating, penetrating through to the substrate. The property measured by this empiric...

This International Standard specifies a method of determining the moulding shrinkage and the shrinkage after heat treatment of moulded test specimens of thermosetting moulding materials. These characteristics are useful for the production control of thermosetting material and for checking uniformity of manufacture. Furthermore, knowledge of the initial shrinkage of thermosettin...

This International Standard specifies methods for measuring the thickness of metallic coatings by the use of X-ray spectrometric methods. The measuring methods to which this International Standard applies are fundamentally those that determine the mass per unit area. Using a knowledge of the density of the coating material, the results of measurements can also be expressed as l...

This International Standard specifies the chemical composition limits for aluminium casting alloys and mechanical properties of separately cast test bars for these alloys. ISO 3522 was prepared by Technical Committee ISO/TC 79, Light metals and their alloys, Subcommittee SC 7, Aluminium and cast aluminium alloys. This fourth edition cancels and replaces the third edition (ISO 3...

This International Standard specifies the safety requirements for the manufacture, application, operation and maintenance of powered industrial trucks. The term "powered industrial trucks" applies to mobile, power-driven vehicles used to carry, push, pull, lift, stack or tier any type of load, as described in clause 3. The word "shall" is to be understood as expressing a mandat...