This British Standard is the official English language version of EN 10151:2002. It supersedes BS 5770-4:1981 which is withdrawn. This European Standard applies to cold rolled narrow strip of thicknesses up to and including 3 mm in rolled widths less than 600 mm made from the stainless steel grades listed in Table 1. The steels are used in the conditions given in Table 4 for t...

This part of this European Standard specifies technical delivery conditions for hot finished hollow sections of circular, square, rectangular or elliptical forms and applies to hollow sections formed hot, with or without subsequent heat treatment, or formed cold with subsequent heat treatment to obtain equivalent metallurgical conditions to those obtained in the hot formed prod...

This part of EN 10210 specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges:Circular: Outside diameters up to 2 500 mmSquare: Outside dimensions up to 800 mm x 800 mmRectangular: Outside dimensions up to 750 mm x 500 mmElliptical: Outside dimensio...

This British Standard has been prepared under the direction of the Iron and Steel and the Non-Ferrous Metals Standards Policy Committees and is the English language version of EN 10233:1993 Metallic materials — Tube — Flattening test, published by the European Committee for Standardization (CEN). No British Standard is superseded. This standard is based on ISO 8492:1986 Metal...

This British Standard has been prepared under the direction of the Iron and Steel and the Non-ferrous Metals Standards Policy Committees and is the English language version of EN 10234:1993 Metallic materials — Tube —Drift expanding test, published by the European Committee for Standardization (CEN). No British Standard is superseded. This standard is based on ISO 8493:1986 M...

This part of EN 10246 specifies requirements for the full peripheral ultrasonic testing of the ends of seamless and welded tubes for the detection of laminar imperfections. The standard specifies acceptance levels and calibration procedures. This part of EN 10246 is applicable to the inspection of welded tubes with an outside diameter greater than 30 mm. No lower limit of wall ...

This part of EN 10246 specifies requirements for automatic eddy current testing of seamless and welded austenitic and austenitic-ferritic steel tubes with the exception of submerged arc-welded (SAW) tubes for verification of hydraulic leak-tightness. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This part of...

This Part of EN 10246 specifies the requirements for automatic eddy current testing of seamless and welded tubes with the exception of submerged arc-welded (SAW) tubes for the detection of imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of the tests. This Part of EN 10246 is applicable to the inspection of tu...

This Part of EN 10246 specifies the requirements for automatic full peripheral magnetic transducer/flux leakage testing of seamless and welded ferromagnetic steel tubes, with the exception of submerged arc welded (SAW) tubes, for the detection of longitudinal imperfections. The standard specifies acceptance levels, calibration procedures and gives guidance on the limitations of...

This Part of EN 10246 specifies the requirements for automatic ultrasonic shear wave testing of seamless steel tubes for the detection of transverse imperfections. The standard specifies acceptance levels and calibration procedures. This Part of EN 10246 is applicable to the inspection of tubes with an outside diameter equal to or greater than 10 mm. European Standard EN 10246...

This Part of EN 10246 specifies the requirements for automatic full peripheral ultrasonic shear wave testing of seamless and welded steel tubes, with the exception of submerged arc-weld (SAW) tubes, for the detection of longitudinal imperfections according to six different acceptance levels (see Table 1 and associated notes). This Part of EN 10246 is applicable to the inspectio...

This part of this European Standard specifies the general technical delivery conditions for open die forgings, forged bars, and products pre-forged and finished in ring rolling mills, for general engineering purposes. General information on technical delivery conditions is given in EN 10021. This European Standard has been prepared by Technical Committee ECISS/TC 28, Steel forg...

This Part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from non-alloy quality and special steels and supplied in the normalized, normalized and tempered, quenched and tempered or annealed condition. General information on technical delivery cond...

This part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from alloy special steel and supplied in the quenched and tempered condition. General information on technical delivery conditions is given in EN 10021. This European Standard has been prepa...

This part of this European Standard specifies the technical delivery requirements for open die forgings, forged bars and products pre-forged and finished in ring rolling mills, manufactured from stainless steels with ferritic, martensitic, austenitic and austenitic-ferritic structures. General information on technical delivery conditions is given in EN 10021. This European Stan...

This British Standard is the official English language version of EN 1168:2005. EN1168 is a candidate “harmonized” European standard and fully takes into account the requirements of the European Commission mandate M/100, Precast concrete products, given under the EU Construction Products Directive (89/106/EEC), and is intended to lead to CE marking. The date of applicability ...

This European Standard specifies the requirements for the ultrasonic examination of steel castings (with ferritic structure) for general purposes and the methods for determining internal discontinuities by the pulse-echo technique. This European Standard applies to the ultrasonic examination of steel castings which have usually received a grain refining heat treatment and which...

This European Standard specifies the requirements for the ultrasonic examination of steel castings (with ferritic structure) for highly stressed components and the methods for determining internal discontinuities by the pulse echo technique. This European Standard applies to the ultrasonic examination of steel castings which have usually received a grain refining heat treatment...

This European Standard specifies the requirements for the ultrasonic examination of spheroidal graphite cast iron castings and the methods for determining internal discontinuities by the pulse-echo technique. This European Standard does not deal with the ultrasonic examination of the nodularity of spheroidal graphite cast irons. This European Standard does not cover the transmi...

This European Standard specifies acceptance levels for indications from surface breaking imperfections in metallic welds detected by penetrant testing. The acceptance levels are primarily intended for use during manufacture !testing", but where appropriate they can be used for in service inspection. The acceptance levels in this standard are based on detection capabilities that...